盐浓度对交联聚合物线团形态的影响

用核孔膜过滤法 (过滤体积对过滤时间作图 )、动态光散射法 (DLS)和扫描电镜法 (SEM )研究了交联反应前后盐 (NaCl)浓度变化对低浓度HPAM与AlCit形成的交联聚合物溶液 (LPS)中交联聚合物线团 (LPC)形态的影响。所用HPAM相对分子质量 1.1× 10 7～ 1.4× 10 7,LPS中HPAM与Al的质量比 2 0∶1,HPAM浓度 0 .1或 0 .2 g/L ,交联反应温度 40℃ ,时间 7天。实验结果表明 :①LPC的平均水力半径Rh(DLS测定值 )随交联反应时盐浓度的增大先减小后增大 ,盐浓度由 0 .5 g/L增加到 2 g/L时Rh 由 45 0nm迅速减小到 2 5 0nm ,盐浓度增加到 2 0 g/L时Rh达到最小值 16 0nm ,此后随盐浓度的继续增加Rh 有所增大 ;盐浓度 0 .5和 2 .0 g/L时Rh 的SEM测定值分别为45 0和 2 5 0nm ,与DLS结果一致。②交联反应完成后改变LPS的盐浓度 ,也可改变LPC的Rh 值 ,但改变幅度较小 ;盐浓度 0 .5 g/L时形成的LPS ,当盐浓度增加至 2 g/L时 ,Rh 值由 45 0nm减小至 35 9nm ,大于盐浓度 2 g/L时形成的LPS的Rh 值 (2 46nm) ;盐浓度 2 g/L时形成的LPS ,当盐浓度减少至 0 .5 g/L时 ,Rh 值由 2 46nm增大至32 6nm ,小于盐浓度 0 .5g/L时形成的LPS的Rh 值 (4 5 0nm)。用盐浓度改变引起LPC水化层厚度改变 ,线团收缩或舒张解释盐浓度改变时Rh 测定值的     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

纤维增强铝基复合材料变形损伤过程声发射研究

采用声发射（ＡＥ）技术，通过测定ＡＥ事件数、幅度和持续时间等发射特征参数以及恒载 Ｆｅｌｉｅｉｔｙ效应，对ＳｉＣ／Ａｌ和Ｃ／Ａｌ两类束丝纤维增强铝昨合在拉伸变形过程中的损失失效特征进行了分析探讨。实验结果表明，纤维种类、界面状况对复合材料损伤过程有着显著的影响，声发射技术是表征这类复合材料损伤特征很有潜力的方法。     

铝冷轧制油应用和生产工艺研究

通过对铝材冷轧工艺的分析。研究，以退火工艺中的斑痕为重点，提出采用加氢处理，异构化精制的石蜡基航空煤油组分为基础油，采用不同复合添加剂生产的通用铝冷轧制油完全可以满足客户要求。     

复式河道漫滩水流计算方法研究

对复式顺直河道和复式游荡型河道中漫滩洪水的计算方法进行了研究.其中，对复式顺直河道，从Shiono-Knight方法出发，将二次流项归并入雷诺切应力项，并将主槽和滩地的流速分布曲线直接相接，推导出一套不需联立求解系数方程组的漫滩水流流速和床面切应力分布的计算公式以及床面平均切应力的解析计算公式；对复式游荡型河道，建立了一种新的上层水流计算方法.文中的计算结果与前人的实验资料基本一致，初步表明文中的方法是合理的.     

开关稳压电源用铝电解电容器的失效机理

概述了开关稳压电源用铝电解电容器的工作状态和失效模式，着重讨论了开关稳压电源用铝电解电容器的开路失效和击穿失效机理。     

Fringe probing of an evaporating microdroplet on a hot surface

The phenomenon of droplets impacting and evaporating on a hot surface is of interest in many areas of engineering. Quantitative measurement of these processes provides great help to reveal the physics behind. A novel technique was developed to quantitatively measure the volume evolution and contact diameter of an evaporating microdroplet on a hot surface utilizing interference fringe scattering method. In this method, fine fringes produced by the interference of two coherent laser beams was scattered by the droplet and projected onto a screen. The profile and volume of the droplet can be derived from the spatial fringe spacing on the screen. The number of total fringes measurable on the screen was used to determine the instantaneous contact diameter of the microdroplet. Validation experiments demonstrated that the measurement errors are less than ±5% and ±1% for microdroplet volume and contact diameter, respectively. By using this method, the dynamic of droplet impingement, evaporation and boiling using ethanol, pure water and water solution of a surfactant (sodium dodecyl sulfate) with impact velocity of 7.5 m/s and diameters ranged from 0.19 to 0.46 mm were investigated.     

塑料挤出型材车间公用工程设计

鉴于当今人们对塑料门窗需求量的增大，通过对5个塑料挤出型材车间的设计，将其公用工程设计整理成文，总结出塑料挤出型材车间的采暖通风设计，压缩空气系统设计，制冷系统设计的较详尽的方案，以供有关设计技术人员参考。     

Engineering Geological Problems of Levee Along Middle and Lower Reaches of Yangtze River

1　ＩｎｔｒｏｄｕｃｔｉｏｎＢｅｃａｕｓｅｏｆｔｈｅｃｏｍｐｌｉｃａｔｅｄｓｕｂｓｏｉｌｐｒｏｆｉｌｅ ,ｔｈｅｌｅｖｅｅａｌｏｎｇｍｉｄｄｌｅａｎｄｌｏｗｅｒｒｅａｃｈｅｓｏｆＹａｎｇｔｚｅ ,ａｂｏｕｔ 36 0 0ｋｍｌｏｎｇ ,ｈａｓｍａｎｙｈｉｄｄｅｎｐｅｒｉｌｓ .Ａｍｏｎｇｔｈｅｄａｎｇｅｒｏｕｓｅｖｅｎｔｓｄｕｒｉｎｇ 1998’ｓｆｌｏｏｄｓｅａｓｏｎｉｎｔｈｅｗｈｏｌｅｖａｌｌｅｙ ,12 .7%ｏｃ ｃｕｒｒｅｄａｌｏｎｇｔｈｅｔｒｕｎｋｓｔｒｅａｍｄｙｋｅｓ,ｏｆｗｈｉｃｈ 6 98ｗｅｒｅｔｈｅｍｏｓｔｄ…     

改性石英砂滤料强化过滤处理含藻水

采用改性石英硝滤料强化过滤处理含藻水的试验结果表明，与石英硝滤料相比，改性石英硝滤料对含藻水具有优良的处理效果；经混凝沉演后水中的余铝对藻类的去除有促进作用。